Canopus MediaEdge-STB3 Einstellungsanleitung

MediaEdge-STB3Setup GuideMediaEdge-STB3Setup GuideNovember 30, 2006Copyright © 2006 Canopus Co., Ltd.All rights reserved.Engineered by Canopus Co., Lt

-2-MediaEdge1 Introduction1-1 Notes regarding usageIN NO EVENT SHALL CANOPUS BE LIABLE TO USER OR ANY OTHER PARTY FOR INCIDENTIAL, CONSEQUENTIAL OR SP

-3-MediaEdge1-3 Canopus websiteIncluding MediaEdge, the latest company information is announced at our website http://www.canopus.com. The latest driv

-4-MediaEdge2 MediaEdge-STB32-1 OverviewMediaEdge is an IP-based video distribution/playing system that consists of a server that stores and distribut

-5-MediaEdge2-2 Features● Supports MPEG-1/2 video SD/HD. ● Supports MPEG-1 Layer-2 audio. ● Provides two VOD modes (Menu mode using VOD menu and Chan

-6-MediaEdge2-4 Operation mode of MediaEdge-STB3 Operating ModesMenu ModeIn this mode, users select and play desired content from a menu screen. The

-7-MediaEdge3 MediaEdge-STB3 Parts Names3-1 Front Panel(1)(2) (3)(4) (5) (6) (7)(1) POWER LED Lights while MediaEdge-STB3 operates. Unlit: Power is

-8-MediaEdge3-2 Rear Panel(1)(3)(4)(2)(8)(5)(6)(9)(7)(10)(11)(12)(13)(1) DVI-D DVI-D signal output.(2) AUDIO OUT-LEFT Audio output (left).(3) AUDIO O

-9-MediaEdge3-3 Remote Controller (1)(3)(3)(4)(4)(5)(5)(6)(6)(7)(8)(8)(2)(3)(4)(5)(6)(8)(1) POWER button Turns power on/off.(2) MENU button Displays

-10-MediaEdge

MediaEdge-11-Chapter 2 - Connecting MediaEdge-STB32This chapter describes the procedures to connect your MediaEdge-STB3 to a stream server (Server PC

Copyright RegulationsIt is illegal for anyone to violate any of the rights provided by the copyright laws to the owner of copyright, except for fair u

-12-MediaEdge1 Connecting to the MediaEdge-SVS3 ServerIn this manual, the setting procedures are explained using the examples under the system where t

-13-MediaEdge1-1 Connecting MediaEdge-STB3Connect MediaEdge-STB3 to the server computer, referring to the diagram below. Keep the following verifi cati

-14-MediaEdge1-2 MediaEdge-STB3 setting using DHCPMediaEdge-STB3 is confi gured to use DHCP at the factory setting. In the example of the MediaEdge net

-15-MediaEdge If the menu screen does not appear:1Press the button on the remote controller to display the system information of the MediaEdge-STB3

-16-MediaEdge6 If you have changed the local settings, enter [User name] and [Password] and then click [Save]. After changing the settings, make sure

-17-MediaEdge1-3 MediaEdge-STB3 setting without using DHCP Setting MediaEdge-STB3 IP Address1Plug the power cord into an outlet, press the RESET butt

-18-MediaEdge2 Use the remote controller and check [Use the following IP address]. 3Specify the IP address with the remote controller. Press the

-19-MediaEdge6 Place the cursor on the [Set] button and press the button on the remote controller. MediaEdge-STB3 will restart, and the screen shown

-20-MediaEdge If the menu screen does not appear:1On the server computer, run a Web browser and open the MediaEdge-STB3 Setup page. Enter the IP addr

-21-MediaEdge1-4 Verify MediaEdge-STB3 operations Verify that the menu screen appearsThe following menu screen will appear a few seconds after the st

Handle the AC adapter cord carefullyDo not place heavy objects on top of the cord, or place it near hot objects. Doing so may damage the cord and resu

-22-MediaEdge● If video does not appear:When [Connecting to server. . . ] dialog box does not disappear, communication with the stream server has fail

-23-MediaEdge2 Connecting to the MediaEdge-LEB/LEB60This section explains how to connect a Canopus live encoder box "MediaEdge-LEB" or a Med

-24-MediaEdge2-2 Setting IP address of MediaEdge-STB3 and URL for menu page Setting MediaEdge-STB3 IP Address1Plug the power cord into an outlet, pre

-25-MediaEdge2Use the remote controller and check [Use the following IP address]. 3Specify the IP address with the remote controller.Press the

-26-MediaEdge Setting menu page URL to MediaEdge-STB31Using the computer for setup, run a Web browser and open the MediaEdge-STB3 Setup page. Enter t

-27-MediaEdge2-3 Verify MediaEdge-STB3 operations Verify that the menu screen appearsA few seconds after the power to the MediaEdge-STB3 is turned on

-28-MediaEdge

MediaEdge-29-Chapter 3 - Setting Up MediaEdge-STB33This chapter describes the details of the operation mode and the operation parameters of the MediaE

-30-MediaEdge1 Setup using Web browser1-1 Accessing the MediaEdge-STB3 Setup pageUse a computer (such as the server) on the same network as the MediaE

-31-MediaEdge[Date/time settings]Sets the clock on the MediaEdge-STB3. [Restart]Restarts the MediaEdge-STB3. [Initialization]Defaults the local settin

CAUTIONThe following conditions indicate the potential for bodily harm, damage to hardware or loss of data.Do not pull AC adapter cord when disconnect

-32-MediaEdge InformationYou can check the settings that are currently in place. [Version]Displays the current fi rmware version of the MediaEdge-STB3

-33-MediaEdge StatusThe Internal status and the operation log of the MediaEdge-STB3 are displayed.

-34-MediaEdge Local settings[System]- Remote Control IDSpecifi es the remote control ID to which the MediaEdge-STB3 responds. Set [Disabled] to disabl

-35-MediaEdge- FEC modeEnables/Disables the FEC (Forward Error Correction) mode. - TelnetSpecifi es if the Telnet function is used. - SNMPSpecifi es the

-36-MediaEdge[Monitor]- Display modeSpecifi es the output mode to the TV monitor. - Monitor aspect ratioSpecifi es the monitor aspect ratio according to

-37-MediaEdge Channel mode settings[User name]Enter your user name. The default user name is [admin]. [Password]Enter your password. No password is s

-38-MediaEdge Date/time setting[User name]Enter your user name. The default user name is [admin]. [Password]Enter your password. No password is set i

-39-MediaEdge Restart[User name]Enter your user name. The default user name is [admin]. [Password]Enter your password. No password is set in the defa

-40-MediaEdge Initialization[User name]Enter your user name. The default user name is [admin]. [Password]Enter your password. No password is set in t

-41-MediaEdge Firmware Update[User name]Enter your user name. The default user name is [admin]. [Password]Enter your password. No password is set in

FCC NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

-42-MediaEdge User name and Password[User name]Enter the current user name. [Password]Enter the current password. [New User name]Enter the new user n

-43-MediaEdge Software LicenseDisplays the license information for the software used on the MediaEdge-STB3.

-44-MediaEdge2 Setup using DIP switches2-1 WOL(Wake On LAN)WOL is a feature that can start the MediaEdge-STB3 via a network when it is in a STOP state

-45-MediaEdgeNote:Pressing the [DISP] button on the remote controller will switch video format as follows:NTSC(J) - 1080/59.94i - 720/59.94p - NTSC(US

-46-MediaEdge3 Updating fi rmware3-1 How to update Updates using a Web browser(1) Copy the firmware archive file to a PC accessible by the MediaEdge-

-47-MediaEdge4 Maintenance Mode4-1 Maintenance Mode overviewMediaEdge-STB3 Maintenance Mode is the recovery program that is used when the fi rmware upd

-48-MediaEdge Starting MediaEdge-STB3 in Maintenance ModeWith the power connected, press and hold down the reset switch. After a few seconds, [POLAR

-49-MediaEdge4-2 Firmware recovery IP address settingWhen DHCP is unavailable, specify the IP address. * In this example, IP address is set to 192. 1

-50-MediaEdge Firmware recoveryRecovers the fi rmware.1: To recover the fi rmware, enter the following: * Do not perform any operations until [root@PO

-51-MediaEdge4-3 If you have forgotten the user name or the passwordIf you have forgotten the user name or the password, you can initialize the MediaE

Product Notes1. Unauthorized copying of a portion or the entirety of this product is prohibited.2. The description and specifi cations of this produc

-52-MediaEdge

MediaEdge-53-Chapter 4 - APPENDIX4- Limitations- Setting Remote Control ID- FEC (Forward Error Correction) Function- MediaEdge-STB3 Hardware Specifi ca

-54-MediaEdge1 Limitations Limitations on playback content- If the MediaEdge-STB3 plays back HD and SD contents seamlessly, the internal MPEG decode

-55-MediaEdge2 Setting Remote Control IDYou can assign the remote control ID numbers (0 to 3) to your MediaEdge-STB3 and remote controller. The defaul

-56-MediaEdge Setting by the DIP switchesRemote control ID can be assigned by the DIP switch setting. The DIP switches can be found under the battery

-57-MediaEdge2-2 Assigning ID to the MediaEdge-STB31Run a Web browser and access the MediaEdge-STB3 setup page. Ex: If MediaEdge-STB3 IP address is se

-58-MediaEdge3 FEC (Forward Error Correction) FunctionsThe FEC (Forward Error Correction) function can correct errors on streaming data. With this fun

-59-MediaEdge4 MediaEdge-STB3 Hardware Specifi cationsNetwork interfaceFormat100Base-TX, 1000Base-TEthernet/IEEE802.3 frame formatAuto negotiation supp

-60-MediaEdgeGeneric I/OSerial portFormat RS-232CConnector D-SUB 9 pin (male) x1Specifi cationVoltageAC adapterInput: AC 100V - 240V (50Hz/60Hz)Output:

Table of ContentsChapter 1 - Before Installation1 Introduction ... 21

Chapter 3 - Setting Up MediaEdge-STB31 Setup using Web browser ..... 301-1 Accessing the MediaE

MediaEdge-1-Chapter 1 - Before Installation1- Introduction- MediaEdge-STB3- MediaEdge-STB3 Parts Names