Canopus ADVC-HDM1 Betriebsanweisung

User’s GuideEngineered by Canopus Co., Ltd.ADVC_HDM1_EN.book Page 1 Tuesday, December 19, 2006 9:20 AM

– 7 –g FORMAT Indicator LEDIndicates the video format being encoded or decoded.On: Indicates the 1080i format.Off: Indicates the 720p format.h RS-422A

– 8 –a LTC Output TerminalThis is the time code output (BNC) termi-nal.The HDV time code is output during HDV decoding.b LTC Input TerminalThis is the

– 9 –Use the DIP switches on the rear panel of the ADVC-HDM1 to set the operation mode. The default setting for all the DIP switches is OFF.* Slide do

– 10 – When using as an HDV to HD-SDI converterPress the [Encode/Decode Switch] on the front panel of the ADVC-HDM1 to turn on the [Decode Selection

– 11 – When using as an HD-SDI to HDV converterPress the [Encode/Decode Switch] on the front panel of the ADVC-HDM1 to turn on the [Encode Selection

– 12 –When using LTC, input the time code to TC IN and press the [Time Code Input Switch] on the front panel of the ADVC-HDM1 to turn on the [LTC Enab

– 13 –With the advanced functions described in this section, the encode bit rate can be changed or encoding can be performed with a full resolution of

– 14 – Benefits of the Advanced FunctionsThese advanced functions are very effective when used for the network transmis-sion of HD video with devices

– 15 –Appendix• Specifications• List of CommandsADVC_HDM1_EN.book Page 15 Tuesday, December 19, 2006 9:20 AM

– 16 –1Specifications1-1 ADVC-HDM1 Hardware SpecificationsVideo input HD-SDI BNC × 1 (HD-SDI)BNC × 1 (ACTIVE THROUGH compatible with SMPTE 292M)Video

 Cautions Relating to the Use of This ProductThis section describes important points to note when using this product.(1) Unauthorized copying of all

– 17 –Advanced encodeMP@HL, MP@H141080, 59.94i/50i 720, 59.94p/50p11-40 MbpsThe advanced mode stream for video transmission is an MPEG2 transport stre

– 18 – RS-232C port RS-422 CONTROLLER port1-2 Connector Pin DiagramsDSUB-9*1Internal short*2Internal shortPin# Signal Name1 (open)2RD3TD4DTR*15GND6D

– 19 – RS-422 DEVICE portDSUB-9Pin# Signal Name1GND2TD–3 RD+4GND5 (open)6GND7TD+8 RD–9GNDADVC_HDM1_EN.book Page 19 Tuesday, December 19, 2006 9:20

– 20 –Block Diagram of ADVC-HDM1 1-3 Advanced Functions ADVC-HDM1LTC OUTLTC INHD-SDI OUTHD-SDI INHD-SDI OUTHD-SDI OUTDC 12VRS422 #1RS422 #2RS232C

– 21 – Serial InterfaceRS-232C, 9600 bps, 8-bit, parity none, stop bit = 1 bit Command List2List of Commands2-1 Remote Control FunctionPL Start play

– 22 –?I Check whether or not there is a current HD-SDI inputFormat: “?I”Status report: “1”: There is an input“0”: There is no inputVB Specify the vid

– 23 – Command List2-2 AV/C Command to RS-422 Conversion ListAV/C Command Deck OperationStop StopX1 PlayAVC_RECORD_RECORD RecordRECORD PAUSE PauseFAS

– 24 –* Sony 9-pin control protocol is used for the output deck control commands.* The details for the AV/C commands are the same as the “Playback Mod

– 25 –If successful, video bitrate in units of 400 bps are returned as follows:operand[6] = video bitrate in units of 400 bps (bit 0 – bit 7)operand[7

CONTENTSChecks ... 1Introduction ...

– 1 –ChecksThis chapter describes the items that should be checked before setting up the ADVC-HDM1 and explains product precautions.• Introduction.• A

– 2 –Regardless of whether negligence occurs during usage, the company assumes no liability, even if there is a claim, for extraordinary, incidental o

– 3 –Please verify that the following components are included in the ADVC-HDM1 pack-age. ADVC-HDM1 AC adapter and AC cable Manual• ADVC-HDM1 User’s

– 4 –z A compact unit compatible with HDV and HD-SDI conversionThe ADVC-HDM1 is a converter unit that can encode HD-SDI signals to the HDV standard or

– 5 –Part Names and FunctionsThis chapter explains the functions of the ADVC-HDM1 parts.• Part Names and Functions• ADVC-HDM1 Input and OutputADVC_HDM

– 6 –a Encode/Decode SwitchPress and hold for more than 1 second to change as follows: [Encode Mode] → [Decode Mode] or [Decode Mode] → [Encode Mode].